INFORMATION
Functions
The voice over fiber multiplexer is point to point fiber transmitting equipment, which realizes 1~8 channel voice (FXO, FXS) POTs phone over fiber and 4 E1,4*100M Ethernet, 4 channel RS232 for option. Its merits include complete warning function, high integration, low consumption, stable performance and convenient usage.
Features
n provides 4 channel E1/ G.703 for option;
n provides 1 channel 100M (liner) Ethernet ports for option
n provides 8 channel voice port, FXO and FXS for option; also for 2/4 wire E&M
n provides 4 channel RS232, rate supports 300-15200 bps for option;
n Ethernet port 10/100M, full/half duplex auto-adaptable and supports VLAN;
n Ethernet port supports AUTO-MDIX (twisted cable and straight cable auto-adaptable);
n 1-8 channel voice connection, supports calling indication;
n Configuration: point to point;
n Voice port supports O port and S port or E&M interface for order, O port connects switch and S port connects user’s phone;
n Optical interface supports SC/FC interface and supports single fiber interface
Optical interface ● Optical wavelength: single mode 1310nm/1550nm
● Fiber: single fiber or double fiber for option
● Transmitting consumption: -9dBm/-5dBm
● Transmission range: 0-50Km/120Km for option
● Optical interface: SC/FC
● Receiving and dispatching module: >-6dBm
● Optical receiver receiving sensitivity <-36 dBm (BER<10-11)
● Fiber circuit code: NRZ code
Ethernet Interface
● Rate: 10/100M, full/duplex auto-negotiation
● Protocol: Support IEEE 802.3, IEEE 802.1Q (VLAN)
● MAC Address Entiries: 4096 Entiries
● Total Memory Sizes: 64MBits SDRAM
● Physical interface: RJ45, support AUTO-MDIX
Voice Phone Interface:
FXS:
Alarm voltage: 75V
Alarmf requency: 25HZ
2 line input impedance: 600Ω (hanging off)
Wastage: 40db
FXO:
Alarm detecting voltage: 35V
Alarm detecting frequency: 17HZ-60HZ
2 line input impedance: 600Ω (hanging off)
Wastage: 40db
E wire:
Max current： 22mA
Saturation voltage: 3V
Dial speed： >20pps
M wire：
steady current： 7 mA
min test current： 5 mA
pluse dial recognition: >20pps
RS232 port
Rate： 300－115.2Kbps auto-adaptable (Asynchronous)
Interface characteristic： satisfies ITU-T V.24
Dimension(19inch rackmount)
2 433mm(L)
2 138mm(W)
2 44mm(H)
Power supply
working voltage range wide, good
anti-disturb and Isolation, work stable
option I – DC-48V,range DC-36V~DC-72C
option II – AC220V,range AC165V~AC240V
Power Consumption: <=3 Watts
Environment condition
Operating temperature: 0C~+50 C
Storage temperature: -20 C~+70 C
Relative temperature:95% (uncondensed)
Related Link:
1. Questions about POTS(fxs/fxo) phone over fiber multiplexer
2. Can POTs Fiber Multiplexer support DSL Transmission?
FAQ:
Question: Can the Fiber Multiplexer be configured as 4Voice+4ETH+4RS232 with SNMP? If can, does the device have VLAN dip switch?
Answer: Yes, the Fiber Multiplexer can be configured as 4Voice+4ETH+4RS232 with SNMP. But the device doesn't have VLAN dip switch. VLAN cannot be set through SNMP, only can be set through console management.
Video:
Phone voice over fiber multiplexer installation guide
Ordering information
Related Products
