INFORMATION
Functions
1~64 POTS (FXO/FXS) over Fiber multiplexer is a kind of point-to-point fiber transmission device. BAUDCOM designed 1~64POTS (FXO/FXS), 1~4channel G.703 E1 and 1~4 channel 100M Ethernet，1~4 channelRS232 transmit over one fiber, and it could match different customer requirement.
|
PRODUCT
CHARACTERISTIC
|
- provides 1~4
channel E1/ G.703 for option;
- provides 1~4
channel 100M (liner) Ethernet ports for option;
- provides
1~64channel POTS( FXO/ FXS),also can offer 2/4 wire E&M for option;
- provides 1~4
channel RS232, rate supports 300-15200 bps for option;
- Ethernet port
10/100M, full/half duplex auto-adaptable and supports VLAN;
- Ethernet port
supports AUTO-MDIX (twisted cable and straight cable auto-adaptable);
- 1~30 channel voice
connection, supports calling indication;
- Configuration:
point to point;
- Voice port supports
O port and S port, O port connects switch and S port connects user’s phone;
- Optical interface
supports SC/FC interface and supports single fiber interface
- 1+1 optical for
protection
|
|
FXO port
|
|
Alarm voltage
|
75V
|
|
Alarm frequency
|
25HZ
|
|
2 line input
impedance
|
600Ω (hanging off)
|
|
Wastage
|
40db
|
|
FXS port
|
|
Alarm detecting
voltage
|
35V
|
|
Alarm detecting
frequency
|
17HZ-60HZ
|
|
2 line input
impedance
|
600Ω (hanging off)
|
|
E&M port
|
|
E wire
|
M wire
|
|
Max current： 22mA
|
steady current： 7 mA
|
|
Saturation voltage:
3V
|
min test current： 5 mA
|
|
Dial speed：
|
Pluse dial
recognition>20pps
|
|
10/100BaseT
Interface
|
|
Number of
Interfaces
|
1~4 port
|
|
Interface Types
|
10/100BaseT
|
|
Standards
Compliance
|
IEEE 802.3
|
|
Protocol
|
User Programmable
HDLC
|
|
Connectors
|
B RJ45 (10/100
BaseT Electrical)
|
|
E1 Interface
|
|
Number
of Interfaces
|
4 port
|
|
Line
Rate
|
E1
(2.048Mbps ± 50 bps)
|
|
Line
Code
|
HDB3
|
|
Electrical
|
ITU-T
G.703
|
|
Jitter
|
G.823
|
|
Impedance
|
75hom/120
Ohms
|
|
Connectors
|
BNC(75ohm)
or RJ45(120ohm)
|
|
Vibration
Characteristic
|
Satisfies
G.742 and G.823 standard
|
|
RS232 interface
|
|
rate
|
30~115.2kbps
auto adaptable (Asychronous)
|
|
Connector
|
RJ45
|
|
Interface
Characteristic
|
Satisfies
ITU-T V.24 standard
|
|
Optical Interface
|
|
Optical
interface
|
SC/FC/ST
|
|
Wavelength
|
1310nm/1550nm
for single-mode optic interface for option
850nm/1310nm
for multi-mode optic interface for option
|
|
Sending
consumption:
|
-9dBm
(regular order)
|
|
Receiving
and dispatching module:
|
>-36dBm(regular
order)
|
|
Optical
receiver receiving sensitivity:
|
<-36
(BER<10):
|
|
Optical
code:
|
NRZ
|
|
Transmit
distance
|
MM
2Km/5Km,SM 20Km/40Km/60 Km/120Km for option
|
|
Mechanical Specifications
|
|
Rack
Mounting
|
Standard
19-inch DIN rack
|
|
Dimension
|
19inch
1 U: 433mm(L)*138mm(D)*44mm(H)
|
|
Management for option
|
|
Web
managed built-in or SNMP central management via chassis
|
|
Power Supply
|
|
Input
AC/DC voltage
|
-48V
DC ( nominal ) / AC also available
|
|
Range
of input
|
-36V
to -72V DC /90V~260VAC
|
|
Temperature
|
0 centi
degree to 55 centi degree
|
|
Humidity
|
95%
RH (non-condensing)
|
|
Cooling
|
Convection
Cooling
|
|
Order information
|
|
BD-OP-MUX64
|
64POTS(FXO/FXS)
over Fiber multiplexer
|
|
BD-OP-MUX64/4E1
|
64POTS(FXO/FXS)
,4E1 over Fiber multiplexer
|
|
BD-OP-MUX64/4E1/4ETH
|
64POTS(FXO/FXS)
,4E1 ,4Ethernet over Fiber multiplexer
|
|
BD-OP-MUX64/4E1/4ETH/4RS232
|
64POTS(FXO/FXS)
,4E1 ,4Ethernet ,4RS232 over Fiber multiplexer
|
|
BD-OP-MUX64/DFI
|
64POTS(FXO/FXS)
over Fiber multiplexer,1+1 fiber for protection
|
|
BD-OP-MUX64/SNMP
|
64POTS(FXO/FXS)
over Fiber multiplexer,web managed or SNMP for option
|
Application
FAQ:
Question: The E1 port on the POTS over Fiber Multiplexer is a RJ45 integrated 2-way E1. What kind of cable should I use to connect the E1 device?
Answer: You can use twisted pair (ordinary network cable) to connect the device, and make sure that the line sequence is correct. One end of the network cable is one RJ45 connector, and the other end is two RJ45 connectors.
Ordering information
Related Products
