MODEL: BD-100M-OAM-SFP
BD-1000M-OAM-SFP
100M 1000M Standalone Managed Media Converter User Manual
1. Function
10/100M、10/100/1000M IEEE802.3ah OAM manageable ethernet fiber media converter can supervise the real time situation of remote manageable fiber media converter and set the functions. With this system, the response speed of the operator is quickened, the daily maintenance and network expenditure of the operators are reduced, and the serving quality of them is enhanced. Pls read this manual carefully before operation.
2. Features
l With high capability chipset, can realize nonbloking transmission to make sure safty and stability
l Support IEEE802.3x、IEEE802.3u、IEEE802.3ab、IEEE802.3z、IEEE802.3d、IEEE802.3ah、IEEE802.1d、IEEE802.1W、IEEE802.1P、IEEE802.1q、IEEE802.3x、TS1000 etc.
l Built-in IP Web interface for remote management and setup
l Layer 2 Managerment Feature
l SNMP VI/V2C moniter /private Enterprise MIB
l Event trap and SNMP trap support
l Managerment VLAN / 16 IEEE802.1Q VLAN groups / Q-in-Q Double Tag VLAN
l Support N*64k
l Supports Maximum frame size to 9k bytes
l TS-1000 OAM / IEEE 802.3ah OAM / Loop Back Test
l Supports Port status/Ethernet statistics on both TP and Fiber interface
3. Technical parameters
Parameters
|
Value
|
Date rate (Mbps)
|
10/100M,10/100/1000M
|
Wavelength (nm)
|
850/1310/1550
|
Fiber type (μm)
|
SM:9/125
MM:50/125
|
Connector
|
SC,ST,FC,LC
|
Transmission
distance (km)
|
20,40,60,80,100
|
Working temp
|
-10～60℃
|
Storage temp
|
-20～70℃
|
Humidity
|
5% ～ 90%on-condensing
|
Dimension(L*W*H)
|
155*128*32mm
|
Power
|
220v or -48v
|
Power dissipation
|
≤3W
|
n Ethernet port
Rate： 10/100M or 10/100/1000M auto-adaptive
Duplex： full/half duplex auto-adaptive
Protocol: supports IEEE802.3，IEEE802.1Q(VLAN)
Physical interface： RJ45
AUTO-MDIX： supports cross line and straight line auto-adaptive
n Optical Interface
Wavelength： 850nm/1310nm (multi-mode)
1310nm/1550nm (single mode)
Interface: SC/FC
Receiving and sending module： >-6dBm
Receiving sensitivity： <-36（BER<10 ）
Transmitting range: Multi-mode2 Km, single-mode 40Km, single-mode 60 Km, single-mode 120Km
4. Working Condition
Voltage： AC180V ~ 240V；DC –48V；DC +24V
Consumption： ≤5W
Operating temperature: 0°C~50°C
Storing temperature: -40°C~+70°C
Relative humidity: 95 %
No causticity and impregnant gas, no rising dust, no strong magnetic field disturbing
5. Installation
5.1 10/100M fiber media converter card
LED indicator lamp:
LED
|
Definition
|
DUP
|
ON: Full Duplex
OFF: Half Duplex
|
100M
|
ON: 100M
OFF:10M
|
TPLNK
|
ON: TX Link connected
Flash: TX signal transmission
|
FXLNK
|
ON: FX link connected
Flash: FX signal transmission
|
OAM
|
ON:IEEE802.3ah OAM enable
OFF:IEEE802.3ah OAM disable
|
PWR
|
ON: Normal
OFF: Abnormal
|
5.2 10/100/1000M fiber media converter card
LED indicator lamp:
LED
|
Definition
|
DUP
|
ON: Full duplex
OFF: Falf duplex
|
1000M
|
ON:1000M
OFF:100M or 10M
|
100M
|
ON:100M
OFF: 1000M or 10M
|
TPLNK
|
ON: TX link connected
Flash: TX signal transmission
|
FXLNK
|
ON: FX link connected
Flash: FX signal transmission
|
OAM
|
ON:IEEE802.3ah OAM enable
OFF:IEEE802.3ah OAM disable
|
PWR
|
ON: Normal
OFF: Abnormal
|
5.3 DIP switches
SW1
|
ON
|
Remote control enable (Central managable side)
|
OFF
|
Remote control closed （default） (Backup Central managable side)
|
SW2
|
NULL
|
Notice: Pls set the Central managable side and Backup Central managable side before power on
(Central managable side media converter card）
(Backup Central managable side media converter card）
5.4 Button introduction:
RST：Recover factory-set
Notice: Press RST for 5 seconds, media converter will recover factory-set
IPAddress:192.168.1.2
Subnet mask:255.255.255.0
Gateway:192.168.1.1
User name:admin
Password:123
5.5 Ethernet port
Ethernet port uses standard circuit sequence as following:
5.6 Optical fiber interface
There is one optical fiber port (SFP slot) on the panel,use can insert the different SFP module as they need.
6. Trouble shooting
If there are problem when installation like below, please solve them as below:
Failure
|
Causing
|
PWR down
|
*Check the power supply of the chassis
*Whether card is inserted firmly
|
TPLNK down
|
*Make sure the connection cable
connects two end firmly
*Check LFP, if it is ON, then disable LFP
*The daterate of media converter does not match with that of the network working device
|
FXLNK down
|
*Fiber connector does not match
with transceiver’s port
*Fiber link dispassion value is over
high, receiving power is lower than the receiving sensitivity.
|
Package loss
|
*Link rate or duplex mode unmatched,
*CAT5 does not connect to RJ45 firmly;Fiber connector does not connect to transceiver firmly
*Wrong configuration of CAT5
|
7.Web Management
7.1 Local/Romote device status information
7.2 802.3ah OAM configuration
7.3 Q-in-Q configuration
